OMC-040, OMC-042 version changes

V2.9 B3
- INW sensors -> Bug fix
- Adding of partial seconds to csv and json data format timestamp when logging frequency is higher than one Hz
V2.9 B2
- Showing in runtime mode when deployment starts, if applicable
- Adding of partial seconds to native data format timestamp when logging frequency is higher than one Hz
- Analog linear conversion function (2 points calibration) -> Measurement point 1 and 2 can now both be reversed (high or low point)
- Bug fix sleep mode for OMC-042 only -> Sleep current was too high (3 mA instead of fewer than 100 uA) (in prior FW2.9 B1 version only)
V2.9 B1
- TCP driver -> Option added for data encryption (AES-128)
- Bug fix NTP driver -> Preventing possible wrong time update when NTP server sends a “Kiss-o'-Death Packet” (very rare occurring) 
- Iridium satellite driver -> Option added for data compacting
V2.8 B1
- Start measurements right after configuration has changed
- Bug fix data sending -> Occasionally occurring SD card failures could cause data loss, especially when sending large data files after long time no network coverage
- Bug fix data download -> Download of to less data (end record was not reached)
- Bug fix data download -> Preventing the apparently for no reason sometimes displayed "file write error" message
V2.7 B1
- Alarm messages driver (previously only SMS) adapted to send alarms also via Email
- Timeout and retries enlarged when receiving temporarily network access denied
- Bug fix Modem maintenance -> Modem firmware upgrade function improved
V2.5 B3
- Bug fix sleep mode -> Sleep current was too high (3 mA instead of fewer than 100 uA) (in prior FW2.5 and FW2.4 versions only)
V2.5 B2
- FTP driver -> Option added for secure file transfer (TLS(explicit))
- TCP latency timeout enhancement (timeout starts now after last byte is transmitted)
- Bug fix Network signal sensor -> retrying when SIM reports busy (CME ERROR: SIM busy)
- External power too low detection removed
- Generic Modbus/RTU sensor driver extended to 20 parameters
- Bug fix HTTP interface -> Communication buffer enlarged to handle huge cookies
V2.4 B7
- Bug fix internal sensors driver -> power sensor reflected wrong current and voltage readings (in prior FW2.4 versions only)
V2.4 B5
- Gonets Satellite modem driver -> Maximum of power down time increased to 20 minutes
- Email driver -> Option added to filter output (data, diagnostics, or both)
- Digital alarm driver -> direct data output on alarm rising/falling if "Direct data output on data alarm" is set
V2.4 B3
- Bug fix serial ports -> suppressing erroneous NULL character output after waking from sleep
V2.4 B2
- Gonets Satellite modem driver added
- General settings -> Option added for data log timestamp round down
- FTP driver -> Option added to omit timestamp in filename
- Bug fix Iridium satellite driver -> Coping with odd behavior of some Iridium modems (missing "READY" after AT+SBDWB=xx command) 
- Iridium satellite driver modified for data output fall back during Email, FTP, TCP or HTTP failures
- Iridium satellite driver modified for sending log data or actual values
V2.2 B6
- Planeta Satellite modem driver added
- Bug fix internal sensors driver -> current can now be measured when supply voltages is above 3.75 Volt
- Bug fix NTP Time update -> Preventing wrong time update when network connection is lost at critical point
- Comport redirect function -> Command echo implemented for SDI12
- SDI12 sensor driver -> Allowing multiple concurrent (aC! and aCX!) commands with the same sensor address
- Additional JSON data format added for Email, FTP and TCP output
- HTTP output driver added
- Modem maintenance function added to test hardware lines (DTR/CTS and DCD)
- DTU driver -> Connect interval independent from data log interval
- Generic serial sensor driver -> Option added for variable waiting time for data
- Digest authentication option added for TCP output
- Bug fix alarm module -> Some odd behavior on data transmission when alarm is cleared and when using alarm intervals in combination with send delay
V2.1 B4
- Starting direct measurement and data log on digital alarm rising/falling
- Bug fix SMS sending -> retrying when SIM reports busy (CMS ERROR 314)
- Bug fix CSV data output format -> parameters without data logging flag were not skipped
- Editing function added for configuration strings (insert mode with arrow left/right and backspace) (OMCTerminal V1.4)
- Bug fix SDI12 sensor driver -> Timeout changed for aM! commands, with measurement times larger than 6 sec
V2.0 B1
- Improved SD card fault recovery handling
- Date format option added for CSV data output
- Additional CSV data format added for TCP output
- Improved Iridium satellite driver added for data sending
- In case of SD card malfunction actual values will be sended at data sending
- Support added for 4GB SD cards
- Maintence menu -> Bug fix for (re)format SD-Card function
- PAP/CHAP authentication option added for APN/VPN login
V1.9 B2
- Bug fix NTP Time update -> When logger was in Alarm mode, the NTP Time update keeps on running continously
V1.9 B1
- Daily operating time slot added for non 24 hours deployment
- Additional CSV data format added for Email and FTP output
- Driver added for snapshot cameras model CAM-S0.3M and CAM-D1.3M
- Working directory added for FTP output
- Analog differential ports -> Bugfix: Parameter value at min and max were not properly stored (only for FW1.8B3, prior versions are OK)
- Comport redirect function -> Bugfix to accommodate large SDI-12 commands (upto 60 characters)
V1.8 B3
- Network signal sensor -> Parameter "Signal bars (0-5)" added for commonly used signal strength representation
- Factor and offset added in parameter settings for conversion of device units to engineering units
- Option added for sensor drivers to use the log interval as sampling interval
- Various small user interface changes, and displaying actual values at Data log
- DTU driver added for a transparent channel between an RS-232, RS-485, or SDI-12 device and host software (TCP-server)
- Code added for direct measurement, and data sending when logger is switched on
- GPS driver option added for calculation of latitude/longitude alarm limits on deployment
- Summer time (daylight saving) option added
- Bug fix TCP Data sending -> skipping "CTRL Z" character incase of accidental data mangling on the SD card, which prematurely ends data sending 
- Digital pulse driver -> Mean Rate parameter calculates now also when quantity parameter is not logged or sample interval is not equal to log interval
- Actual Values Overview -> "Timeout" replaced by "No response", if sensor does not work correctly
V1.7 B9
- Hybrid feature added to use module power as digital alarm output 
- NIVUS KDO sensor driver added
V1.7 B8
- Generic Serial driver option added for using output start commands
V1.7 B7
- Bug fix SDI12 sensor driver > Timeout and retry changed to prevent timeout for sensors with more than approximately 6 to 10 parameters
- Bug fix SMS alarm driver -> Now sending HI Alarm SMS intead of Solved SMS, when Alarm drops under HIHI, but still above HI Alarm threshold
V1.7 B6
- Bug fix Radio output driver -> Power down and send delay did not work correctly
V1.7 B5
- Maintence menu -> Function added to (re)format SD-Card
V1.7 B4
- Small bug fixes for TCP terminal use (keeping open TCP link when closing the menu, and closing menu mode when loosing connection)
- FTP driver -> Option added for active (default) and passive FTP mode
V1.7 B2
- Option added for continuous alarm sampling (Be aware, this is not a very low power option!)
- Generic Modbus/RTU sensor driver extended to 16 parameters, and Bit status register type added
- Display driver added
- Bug fix Digital pulse driver -> Mean rate calculation when there is an alarm log interval, and no sample alarm interval
- SDI12 sensor driver extended with the measurement commands aC1! till aC9! and aM! till aM9!
V1.6 B9
- EXO sensor driver adapted for both new and old data layout
V1.6 B8
- Bug fix Digital pulse driver -> Counter register increased by one at every logger restart, if port mode was internal Pull Up
V1.6 B7
- Bug fix Generic Modbus/RTU driver -> Sometimes a driver timeout when reading more than one or two parameters, and option RS485 8N2 added
V1.6 B6
- Bug fix Independent data log for GPS and GSM signal driver -> wrong parameters were tagged as logged
V1.6 B5
- GPS sensor -> Option added to power the GPS either by the Sensor or by the Module power switch
V1.6 B4
- Improved battery life calculation when Modem is on (Idle) during sleep
V1.6 B3
- Digital pulse sensors -> Option added to log each counter change event (e.g. for time registration of bucket tipping events in rain gauge applications)
V1.6 B2
- Code optimizing with retry mechanism, to cope with accidental faltering SD-Card
- Verbose Modem and Network error messages
V1.6 B1
- Analog sensors -> User determined linear conversion function (2 calibration points) implemented
- Analog differential sensor drivers added for hardware revision 9
V1.5 B9
- 20 seconds and 20 minutes logging and sample interval added
- Extended parameter list added for EXO sensor driver
V1.5 B8
- STS DTM sensor driver added
- SDI12 sensor driver extended to 20 parameters
V1.5 B7
- INW DO sensor -> Bug fix
- Modem internal baud rate lowered from 115K2 to 57K6, due to incidental character overrun during poor GPRS coverage
V1.5 B6
- Analog sensors -> Bug fix: Auto calibration function was wrongly implemented
V1.5 B2
- Configuration menu -> Bug fix: Accidental removing of TCP/FTP/Email driver after removing of a Sensor driver (only when the TCP/FTP/Email driver was added after the the Sensor driver)
V1.5
- EXO sensor driver added
V1.4 B8
- Modem settings -> Deregister network added in provider selection, to solve network access denied situation, due to network blacklist
V1.4 B7
- Maintence menu -> Field test Prepaid balance (if applicable) added
V1.4 B6
- Automatic NTP time update, incase of lose of time due to static discharge, or backup battery failure, or else
- Network registration and APN login timeouts increased from about 30 seconds to 1 minute
- Improved retries for zending of longer data files (> 100K of data)
V1.4 B4
- Internal sensors -> Power measurement retries increased, to avoid incidental repeating power error and solved SMS
- Various user interface bugs fixed (no operational impact)
- INW DO sensor driver added
V1.4 B3
- Bug fix SD-Card code -> Support added for other Micro SD-Cards
V1.4 B2
- Generic MODBUS/RTU driver added
V1.4
- Digital pulse sensor -> Mean, Max and Min Rate parameters added
- Internal sensors -> Min and Max Voltage parameters added
- Maintence menu -> Field test Battery resistance added
- SDI12 sensor drivers added for Generic, INW and OTT sensors
- ISOMAG ML255 sensor driver added
V1.3 B4
- Digital sensors -> Internal Pull Down or Pull up added for digital input
- INW PT12 sensor -> Bug fix (skipping first invalid '0' reading)
V1.3 B3
- Digital sensor -> Input alarm driver added
V1.3 B2
- SMS Commands -> Bug fix: Logger didn't process SMS messages in the 2 Cycle, and didn't go to sleep anymore
V1.3
- Interface with OMC-Programmer (V1.6)
V1.2 B6
- Modbus sensoren -> Bug fix INW sensoren
V1.2 B3
- INW PT12 sensor -> Reported slave ID will now be detected
V1.2
- Terminal Link Request in TCP protocol via OMC-Data-Online server
- USB port disabling after 5 minutes inactivety on USB port, inorder to preserve power
- Operating cycle time takes now configuration and firmware upgrade time into account
V1.1 B5
- Digital sensor -> Rate parameter removed
V1.1 B4
- Digital sensor -> Quantity parameter is now quantity inbetween data logging intervals instead of inbetween sample intervals
- Digital sensor -> Option to preset pulse counter value added
- McVan NEP39x sensor -> Bug fix data input reading
V1.1
- Maintenace menu -> Down- and Upload of configuration file added 
- INW CT2X sensor -> Salinity parameter added
- Internal sensors -> Battery relaced attribute now defaults to Yes at first instance, or at first config upload
V1.0
- First version